（US Stock） 4.5KW ATC Automatic Tool Change Air Spindle Motor BT30 800HZ 220V CNC

$1768.0 Buy It Now or Best Offer
free,30-Day Returns

Seller Store powace1515
(3032) 99.6%,

Location: Los Angeles
Ships to: US,
Item: 114389590678

Restocking Fee:No
Return shipping will be paid by:Buyer
All returns accepted:Returns Accepted
Item must be returned within:30 Days
Refund will be given as:Money back or replacement (buyer’s choice)
RATTM MOTOR:RATTM MOTOR
Speed:3000-24000rpm
Cooling:Air cooled
Phase:3
Nose:BT30-ER25 tool holder
Voltage:220V
RTM120x103-30-24Z/4.5 220V:RTM120x103-30-24Z/4.5 220V
Nominal Rated Input Voltage:220 V
MPN:Does not apply
Current:10.7A
Power:4.5KW
Pole:4 Pole

【USA Stock】（US Stock） 4.5KW ATC Automatic Tool Change Air Spindle Motor BT30 800HZ 220V CNCfor CNC Router Milling Engraving Machine Good New:We have USA Warehouse in United States,so we will ship this item from USA Warehouse to you. Package included:1 x 4.5KW ATC Automatic Tool Change Air Cooled Spindle Motor 220V ( 24000rpm,10.7A,800Hz, 4pcs bearing )1 x BT30-ER25 Tool Holder with 45° pull stud2 x Aviation plugEnglish user manual Notice: if you also need the inverter,pls contact us via ebay message. 100% Brand New and High Quality!!! This listing does not include the above VFD 1) This spindle is built-in type spindle motor, built-in three asynchronous motors,by the inverter control.As the spindle has a compact structure,high power, big torque, small vibration, low noise characteristics,so it can achieve high speed,high powe cutting,high precision and high stability operation.2) The bearing of spindle use grease lubricated angular to contact bearings,can be achieved lifelong lubricating within the life cycle. 3)The atc spindle uses air cooling to cool the motor and front and rear bearings. The wind is provided by the fan at the rear end, from the rear of the spindle through the inner and outer air slots directly to the front of the spindle, thereby taking away the heat generated by the high-speed rotation of the spindle, achieving thermal balance, and keeping the temperature of the electric spindle within a certain value.4) The spindle built-in PTC 140 temperature sensor(Technical parameters are visible in other sections of this specification),you can read it anytime if you need to protect the motor temperature.5) The tool clamping methods:this spindle built-in automatic tool change device,shank form is BT30. Please note that when stopping the spindle, you need to wait until the spindle is stopped before using the tool, so as to avoid causing the spindle and the tool mechanism to be connected together and cannot be separated. When loosening the tool and broaching the tool, you need to return the air, and pls keep the air intake and return air during the whole work. ProducttEchnicalparameter tableSpindlemODEL:RTM120X103-30-24Z/4.5220vVoltage:220VMaximum speed:24000rpmMax frequency:800HZElectric current:15AMotor Pole:4 PoleRAted power:4.5KW(S1)Peak power:5.4KW(S6)Rated Torque:3.5NMPeak Torque:4.2NM 4.5kw air-cooled automatic tool change spindle is a high-end woodworking company designed to develophigh-power electric spindle bearings imported fom Germany, high-precision bearings, high precision, long life.The electric spindle fan cooling with Road gas seal structure, automatic tool changer with bt30 tool holder, feastautomatic tool change and improve the efficiency of the automated processing. Procuct Name4.5KW air-cooled ATC spindlePower4.5KWVoltage220VTorque3.5Nm (Torque peaked at 12000 rpm)Speed3000~24000rpm/minMax Frequency800HzCurrent10.7AColletBT30Pole number4Cooling Type air coolingBarometric pressure6 barFixed wayTwo side,screw fixedNumber of phases3Bearing2*7008 +2*7006Warranty3-year Product characteristic curve graph: Wiring definitionPower Supply, Fhermal, FanProximity switch and push button switchDetails:TEchnicalparametersNo.PRojectStandard1SpindleblowingDust/seal gas pressure (MPa)0.2-0.252Spindlegas seal gas flow(L/min)65 + 10 (When onWORKING)3Cooling water pressure (MPa)≧0.254Cooling water flow (L/min)≧2.55Cooling water temperature(℃)24-286Spindlestatic state pulse(M)≦37Spindlevibration (Mm/s)≦1.08Spindleassembly methodBottom mounting(6-M8)9MotorwindingsPressure test (V/M)1000V/1 minute withstanding Voltage test10Tool InterfaceBT3011Inverter Specifications5.5KW(220V)12fitmentWoodworking machinery, polishing industry, etc.Spindleinstallation explanation1) Fan cooling systemDescriptionWhen the spindle rotates, the rear fan system must be started TOensure the correct supply voltage and the supply voltage is 12v.2) Air Sealing control(AS)In order TOprevent water or impurities enters internal of the spindle,spindle will have gas SealingDevice,the gas seal machine must be started start with the machine at the same time. And the need TOgo throughmulti-stage filtration.3) Compressed gas quality requirementsThe quality requirement of gas whichis used in gas seals:Oil Content:﹤0.01mg/m³Solid particle:< 5 * mPressureDew point:< 7.5Degrees C(0.7mpa)4) Running-in program instructionsOnly all monitoring issued no failures operational signals,at the same time,all safetyDevices have been installed and working properly,then allow start spindle.Note: new or spindlewhichIs not used for a long time must TObe running slowly.First,start run spindle for half an hour as 25% of the maximum speed,then increase TO50% of the maximum speed,TOrun 15 minutes,finally, increase TOmaximum speed.It 's need TOcheck the temperature of the spindleDuring the wholeProcess,Spindle will get hot, but not hot hand, if the spindle becomes hot, pls stop the operation and contact our customer serviceDepartment.5) Productbackend interface instructionsNo.FunctionDEfinition1GAS Sealing(Protection of impurities inTOthe spindle0.2-0.25MPa)Ф62Return air (piston reset 0.35-0.45MPa)Ф65Power Supply (Spindlepower lines with thermistor)U/V/W/ Ground wire6Intake air (Spindleloose knife0.5-0.6MPa)Ф67sensor(spindle tool change signals 24V)Broach / loose knife8Fan(spindle cooling)12v6) PTC140Temperature coefficient thermistor parametersOur products are equipped with a single thermistor PTC140, it can be used for spindle temperature protection.Parameter nameParameter symbolSingle CoreThree core Series connectionUnitMaximum DC working temperatureUmax3030VRated control temperatureTKDesigned according TOuser℃Rated control temperaturetoleranceT1±5℃±5℃℃Rated control temperaturetoleranceT2±0.5℃±0.5℃℃Resistance value on 25℃r25≤100≤300ΩRated control temperatureOn -5℃resistance valueTK-5℃≤550≤1600ΩRated control temperatureOn +5℃resistance valueTK+5℃≥1330≥4000ΩRated control temperatureOn +15℃resistance valueTK+15℃≥4≥12KOThermal response timeTA≤5≤5SDielectric StrengthUisAC2.5AC2.5KVMaximum control temperatureTKmax180180℃Maximum allowable storage temperaturetmax180180℃Minimum allowable storage temperatureTmin-40-40℃7) ProductTool ChangeSignalsdescriptionsensor MODEL(0-24V, PNP), The spindle built two sensors.wiring Diagram is as follows:1. Response broach knife signal, when theKnife handleIs hang,black sensor output signal;2. Response loose knife signal, when theKnife jawsOpen,black sensor output signal; BT30-ER25 Tool Holder with 45° pull stud About us:Our company is an emerging professional Cross-Border Electronic company.We,as an honor and responsible seller online,always try our effort to offer best quality and service to our customers with our 100% sincerity.We guarantee every product is of high quality and durable utility compared to other factories becayse we choose the best-buys goods. Besides,our company has a powerful technical support and perfect after-sales service. Shipping:All items will be sent out with tracking within 1-2 business day after the payment received,may be a delay on weekends; Return&Refund: 1.Any reason required for all refund.Item must be in it's original condition and no physical damage,buyer responsible for all shipping cost.2.When you have the parcel,and not satisfied the goods or it is other problem like as broken,pls tell us the detail reason and provide the photos,we will help you to solve any problems.

Frequently Asked Questions About （US Stock） 4.5KW ATC Automatic Tool Change Air Spindle Motor BT30 800HZ 220V CNC in My Website

www.fibusfamilyfoundation.org is the best online shopping platform where you can buy （US Stock） 4.5KW ATC Automatic Tool Change Air Spindle Motor BT30 800HZ 220V CNC from renowned brand(s). www.fibusfamilyfoundation.org delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.

What are the best-selling （US Stock） 4.5KW ATC Automatic Tool Change Air Spindle Motor BT30 800HZ 220V CNC on www.fibusfamilyfoundation.org?

Frequently Asked Questions About （US Stock） 4.5KW ATC Automatic Tool Change Air Spindle Motor BT30 800HZ 220V CNC in My Website

What are the best-selling （US Stock） 4.5KW ATC Automatic Tool Change Air Spindle Motor BT30 800HZ 220V CNC on www.fibusfamilyfoundation.org?

Leave a Reply Cancel reply