For Nissan Pathfinder 1998-2003 Infiniti QX4 Rear Shocks Struts Absorbers

$39.17 Buy It Now or Best Offer
free,30-Day Returns

Seller Store
() %,

Location:
Ships to: US,
Item: 186246519446

eBay 1.Fitting the Following Vehicle: 1998-2004 Nissan Pathfinder Excludes Armanda & Adjustable Suspension – From Production Date 12-1998 1998-2003 Infiniti QX4 4WD Only 2.Note Please check above compatibility list to make sure it fits your vehicle. * Recommended replacement cycle Since the average annual distance of the car is 20,000 kilometers, and the shock absorber needs to be replaced in pairs, the replacement frequency is obtained every 4 years. In fact, the replacement frequency will vary depending on the car condition, road condition and shock absorber manufacturer. For Nissan Pathfinder 1998-2003 Infiniti QX4 Rear Shocks Struts Absorbers 1.Fitting the Following Vehicle: 1998-2004 Nissan Pathfinder Excludes Armanda & Adjustable Suspension – From Production Date 12-1998 1998-2003 Infiniti QX4 4WD Only 2.Note Please check above compatibility list to make sure it fits your vehicle. * Recommended replacement cycle Since the average annual distance of the car is 20,000 kilometers, and the shock absorber needs to be replaced in pairs, the replacement frequency is obtained every 4 years. In fact, the replacement frequency will vary depending on the car condition, road condition and shock absorber manufacturer. * The following methods can be used to check whether the shock absorber works well 1. Under normal circumstances, oil leakage in the shock absorber means that there is a problem with your shock absorber. You should repair it at this time to avoid abnormal operation of the shock absorber. 2. Press the bumper firmly, and then release it. If the car jumps 2 or 3 times, it means that the shock absorber is working well. 3. When the car is driving slowly and braking urgently, if the car vibrates violently, it means there is a problem with the shock absorber. 4. The car stops after driving 10km on the road with poor road conditions and touches the outer shell with your hands. If the temperature is not high enough, it means that there is no resistance inside the shock absorber and the shock absorber does not work. At this time you should know if it is time to replace the shock absorber. * Complete Strut Assembly Structure * Removal and Installation Guideline * Frequently Asked Questions 1.Can I Drive With a Broken Strut? A strut is a suspension component that dampens an automobile’s movements and prevents it from bouncing on its springs. Struts are often expensive to replace, but driving on a broken strut is not a good idea. 2.Can worn shocks or struts cause my new tires to wear unevenly? Absolutely: shocks and struts provide damping force to control tire movement. When the tires move excessively, they develop a “cupping” wear pattern that damages the tire. Other factors such as incorrect air pressure, worn suspension components or improperly aligned steering also causes uneven tire wear. 3.What are the benefits after replacing the shock absorber? Buffer conveys shock to drivers and passengers in order to improve ride comfort and reduce fatigue. Extend body life, prevent spring damage and improve braking effect. Suppressing the rapid vibration of the wheels while driving, preventing the tires from leaving the road surface and improving the driving stability. Improving driving stability and adjustability, effectively conveying engine deflagration pressure to the ground, so as to save fuel costs. * Precautions for replacing the shock absorber 1. When installing a new shock absorber, you should pay attention to whether the model matches, please pay attention to the matching model list before purchasing, and confirm whether the left and right are correct. 2. Check the quality status of the new shock absorber, such as whether there is oil leakage in the appearance, etc., pay special attention to the surface of the piston not to be bumped. 3. Professional tools must be used during installation, and the shock absorber must not be forcibly installed. 4. Pay attention to whether the installation position between the shock absorber and the body and the car is correct. 5. During the assembly process, be sure to protect the surface of the piston rod, and avoid using tools to pull the piston rod or bump or scratch the piston rod, otherwise the shock absorber will leak oil. 6. All nuts should be new and tightened according to the specified parameters of the vehicle to ensure that the tightening torque of the connection part meets the specified parameters of the vehicle. 7. When tightening the nuts of the connecting part, it should be carried out in the natural state of the tire and meet the specified parameters of the vehicle. If you are interested with any other suspension parts, please click and save our store. Ball Joint Replacement Guideline: If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension. Picture(A) The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty. Picture(B) 1.Raise the vehicle and remove the front wheels. 2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes. Picture(C) 3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts. Picture(D) 4.Loosen and remove the fixing nut of the ball joint on the steering knuckle. Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket. Picture(E) 5.Remove the bad or worn ball joint from the control arm. 6.Loosen the compression ball joint on the steering knuckle using a suitable special tool. Picture(F) 7.Clean the cone connection. Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface. Picture(G) 8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts. 9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. 10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary. 11.Finally, carry out a test drive. Sway Bar Stabilizer Link Replacement Guideline: While driving, the following signs may indicate a faulty sway bar stabilizer link: (1).Rattling and thumping noises on rough roads. (2).Imprecise vehicle handling. (3).Stronger inclination of the vehicle during cornering. If the sway bar stabilizer link is found to be defective, it should be replaced as described below. Picture(A) 1.Raise vehicle and remove front wheels. Tip:Always check both stabilizer links and replace them in pairs if necessary. 2.Spray fastening nuts of the stabilizer link with rust remover and let act for a few minutes. Picture(B) 3.Loosen the lower fastening nut of the stabilizer link at the stabilizer and remove. Tip:If the ball stud also starts to turn, hold it with a suitable tool. 4.Press stabilizer link out of torsion bar. Picture(C) 5.Loosen the upper fastening nut of the stabilizer link at the suspension strut and remove it. Tip:If the ball stud also starts to turn, hold it with a suitable tool. Picture(D) 6.Press stabilizer link at suspension strut out of bracket. Picture(E) 7.Insert new stabilizer link at suspension strut. Picture(F) 8.Tighten stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(G) 9.Insert new stabilizer link at stabilizer. 10.Tighten stabilizer link at stabilizer to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(H) 11.Remount the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. Tip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension. 12.Conclude with a test drive. Tie-Rod End Replacement Guideline: If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods. Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely. This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod. Picture(A) Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance. 1.Lift the vehicle and dismount the front axle wheels. 2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes. Picture(B) 3.Dismount the front underride guard. Picture(C) 4.Loosen the fastening nut from the tie rod and remove it completely. 5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator. Picture(D) 6.Remove the clamp of the bellow on the steering gear. 7.Push the bellow towards the tie rod end. Picture(E) 8.Unscrew the inner tie rod from the rack. 9.Clean the sealing face of the bellow at the steering gear. Picture(F) 10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle. Note:Always use new self-locking nuts and bolts for a reliable repair. 11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle manufacturer. Picture(G) 12.Mount the bellow and close the clamps with the appropriate special tool. Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance. Picture(H) 13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer. Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure. Tip:Secure the ball stud against twisting with a suitable tool. Picture(I) 14.Mount the front underride guard. 15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer. 16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications. 17.Perform a test drive. Note:When performing the test drive, pay special attention to the handling while cornering and listen for possible noise emission. Frequently Asked Questions (1).Do I need to replace the control arm if the bushings are worn? Because the weight of the car is transferred through the control arm two rubber bushings are fitted at the pivot point and bolted to the frame. Road conditions and driving habits can contribute to the wear of these bushings which will become worn and fall apart. These bushing can be inspected by raising the car up and looking for an irregular configuration of the rubber center of the bushing. Many control arms have the ball joint manufactured into the arm which will be replaced along with the control arm itself. When one control arm is worn it is highly advised to replace the opposing arm. (2).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel. Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control. If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious. Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car. (3).What happens if I don’t replace ball joints? If you don’t want to replace your ball joints, then get ready to experience some serious issues. The old ball joints cause mysterious clunking noise or drifting steering. Once they are worn-out, it will seriously affect your steering and suspension. However, you do not need to change the ball joints if it is new. Item Specifics Brand carmasuspensi Manufacturer Part Number CS995072S01 Type Strut Assembly Fitment Type Direct Replacement Placement on Vehicle Left Manufacturer Warranty 1 Year Features Sealed Modified Item No Adjustable No Gas Charged Shock Yes Interchange Part Number 343379 Other Part Number 37204 Kit or Single Part Kit Kit Parts Included Set of two rear struts Surface Finish Powder Coat OE Spec or Performance/Custom OE Spec Color Gloss Black Return Policy Free return or replacement within 30 days Shock Absorber System Double Pipe Shock Absorber Type Gas Vintage Car Part No Material Steel Mounting Style Screw-On Performance Part No Quantity 2Pcs Superseded Part Number Shock and Strut Universal Fitment No Included Hardware Mounting Hardware Item Length 24.250″(R) Gross Weight (LB) 9.039 Compressed Length 15.125″(R) Package Dimension (in.) 19.69*4.72*2.36 Travel Length 9.125″(R) Part Name Shock Absorber and Strut Assembly Discount Targeted Disounts Terms (1).Targeted Discount Terms only apply to auto parts purchased from CARMASUSPENSIONS, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).If you have reached any targeted discount threshold(s), please contact our customer services after you received all your items. (3).Targeted Discount will be refunded from buyer’s payment, which means CARMASUSPENSIONS won’t provide any extra targeted discounts if full refund is issued. Targeted Shipping Discount (4).Since our warehouse is located in Los Angeles, California, therefore you are qualified for extra 2% targeted shipping discount off the item sales if shipping address of your order is in California(CA), Washington(WA), Oregon(OR), Nevada(NV). If you have reached this targeted shipping discount threshold, please contact our customer services after you received all your items. Note: Item sales means your payment for the product(s) only, excluding shipping and handling charges, US internet sales taxes. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).CARMASUSPENSIONS has the final power of interpretation of all the above Targeted Discount Terms and Procedures. Shipping WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm. (1).Warehouse is located in Los Angeles, California, where local pickup transaction is temporarily not available. (2).Shipping services only cover 48 states and Washington DC in US Continental, while most of the time Alaska, Hawaii, Puerto Rico, American Samoa, U.S. Virgin Islands, Northern Marianas, Guam are not deliverable. (3).USPS PO Box, APO Army Post Office, FPO Fleet Post Office addresses are not available. (4).Global Shipping Program is temporarily not available due to the reason for package dimensions. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Your auto parts sometimes might be shipped with two or more separated packages due to weight limitation, please keep patient with no Item Not Received claim or Return request filed until by all of your items are received. (7).Seller is required to purchase signature confirmation to be protected if a buyer reports an item not received or opens a payment dispute if the order has a total cost (including shipping costs and any taxes) of $750 or more. Warranty Items valued over $15 on eBay that include a warranty or service contract must contain additional details in seller’s listing description. 10 Year Warranty Terms and Procedures (1).The warranty terms only apply to the auto parts purchased from CARMASUSPENSIONS, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).CARMASUSPENSIONS carries no warranty responsibilities for any auto parts removing fees, installation fees, consulting fees, labor costs, towing charges, rental car reimbursements. (3).The stated 10 year warranty is limited to only one brand new replacement for each part purchased during 10 year warranty time period. (4).CARMASUSPENSIONS promises free replacement due to quality defects or item not as described issues within 90 calendar days from the date when buyers receive their items in the situation when buyers are willing to provide convictive proofs or professional diagnose report if required, otherwise CARMASUSPENSIONS has the right to refuse any replacement requests. (5).CARMASUSPENSIONS promises free replacement due to quality defects or item not as described issues after 90 calendar days from the date when buyers receive their items in the situation when buyers promise to prepay 15% of the original item sales price as postage for replacement, otherwise CARMASUSPENSIONS has the right to refuse any replacement requests. (6).CARMASUSPENSIONS carries no warranty responsibilities for any replacement due to car accidents, drag racing, unprofessional replacement, road hazard, disassembly. (7).Anyone who attempts to execute 10 year warranty procedures must be the original purchaser of the item(s), otherwise 10 year warranty terms void immediately. (8).Anyone who attempts to execute 10 year warranty procedures must provide screenshot of his or her original eBay order details if required, including buyer user name, shipping address, item title, item id, final sales price. (9).CARMASUSPENSIONS has the final power of interpretation of the above 10 Year Warranty Terms and Procedures. Return (1).Most of items support 60 Days Money Back Guarantee. (2).Refunds will be credited within 2 or 3 business days after returned item(s) is received. Best Sales For Chevrolet Malibu Pontiac G6 Saturn Aura 8 x Control Arm Sway Bar Tie Rod Kit USD 111.59 For 1999-06 Chevy + GMC 1500 Trucks 6-Lug 4×4 Complete Front Suspension Kit x13 USD 110.19 For Chevy GMC C1500 C2500 Suburban Tahoe 15Pcs Front Control Arms Sway Bars Kit USD 213.99 For Ford Ranger & Explorer 4WD 10Pcs Front Control Arms Ball Joints Tie Rods Kit USD 79.79 Fits Ford F-250 F-350 Super Duty – 4WD 4×4 New 5x Complete Front Suspension Kit USD 108.29 Newly Listed Front Catalytic Converter For 2001-2004 Toyota Sequoia 4.7L Left EPA 55443 USD 84.91 14x Front Control Arm and Ball Joint Wheel Hub Bearing Fits 05-10 Chrysler 300 USD 282.38 Catalytic Converter EPA For 2012 2013-2018 Ford Focus 2.0L 641514 Direct-Fit USD 143.60 Catalytic Converter For Chrysler 2008 2009 2010 Town & Country 42912 Direct Fit USD 102.86 Rear Pair Shock Absorber Assembly Kit Fits for 2011-2015 Chevrolet Cruze Strut USD 41.37 For Nissan Pathfinder 1998-2003 Infiniti QX4 Rear Shocks Struts Absorbers 1.Fitting the Following Vehicle: 1998-2004 Nissan Pathfinder Excludes Armanda & Adjustable Suspension – From Production Date 12-1998 1998-2003 Infiniti QX4 4WD Only 2.Note Please check above compatibility list to make sure it fits your vehicle. * Recommended replacement cycle Since the average annual distance of the car is 20,000 kilometers, and the shock absorber needs to be replaced in pairs, the replacement frequency is obtained every 4 years. In fact, the replacement frequency will vary depending on the car condition, road condition and shock absorber manufacturer. * The following methods can be used to check whether the shock absorber works well 1. Under normal circumstances, oil leakage in the shock absorber means that there is a problem with your shock absorber. You should repair it at this time to avoid abnormal operation of the shock absorber. 2. Press the bumper firmly, and then release it. If the car jumps 2 or 3 times, it means that the shock absorber is working well. 3. When the car is driving slowly and braking urgently, if the car vibrates violently, it means there is a problem with the shock absorber. 4. The car stops after driving 10km on the road with poor road conditions and touches the outer shell with your hands. If the temperature is not high enough, it means that there is no resistance inside the shock absorber and the shock absorber does not work. At this time you should know if it is time to replace the shock absorber. * Complete Strut Assembly Structure * Removal and Installation Guideline * Frequently Asked Questions 1.Can I Drive With a Broken Strut? A strut is a suspension component that dampens an automobile’s movements and prevents it from bouncing on its springs. Struts are often expensive to replace, but driving on a broken strut is not a good idea. 2.Can worn shocks or struts cause my new tires to wear unevenly? Absolutely: shocks and struts provide damping force to control tire movement. When the tires move excessively, they develop a “cupping” wear pattern that damages the tire. Other factors such as incorrect air pressure, worn suspension components or improperly aligned steering also causes uneven tire wear. 3.What are the benefits after replacing the shock absorber? Buffer conveys shock to drivers and passengers in order to improve ride comfort and reduce fatigue. Extend body life, prevent spring damage and improve braking effect. Suppressing the rapid vibration of the wheels while driving, preventing the tires from leaving the road surface and improving the driving stability. Improving driving stability and adjustability, effectively conveying engine deflagration pressure to the ground, so as to save fuel costs. * Precautions for replacing the shock absorber 1. When installing a new shock absorber, you should pay attention to whether the model matches, please pay attention to the matching model list before purchasing, and confirm whether the left and right are correct. 2. Check the quality status of the new shock absorber, such as whether there is oil leakage in the appearance, etc., pay special attention to the surface of the piston not to be bumped. 3. Professional tools must be used during installation, and the shock absorber must not be forcibly installed. 4. Pay attention to whether the installation position between the shock absorber and the body and the car is correct. 5. During the assembly process, be sure to protect the surface of the piston rod, and avoid using tools to pull the piston rod or bump or scratch the piston rod, otherwise the shock absorber will leak oil. 6. All nuts should be new and tightened according to the specified parameters of the vehicle to ensure that the tightening torque of the connection part meets the specified parameters of the vehicle. 7. When tightening the nuts of the connecting part, it should be carried out in the natural state of the tire and meet the specified parameters of the vehicle. If you are interested with any other suspension parts, please click and save our store. Ball Joint Replacement Guideline: If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension. Picture(A) The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty. Picture(B) 1.Raise the vehicle and remove the front wheels. 2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes. Picture(C) 3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts. Picture(D) 4.Loosen and remove the fixing nut of the ball joint on the steering knuckle. Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket. Picture(E) 5.Remove the bad or worn ball joint from the control arm. 6.Loosen the compression ball joint on the steering knuckle using a suitable special tool. Picture(F) 7.Clean the cone connection. Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface. Picture(G) 8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts. 9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. 10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary. 11.Finally, carry out a test drive. Sway Bar Stabilizer Link Replacement Guideline: While driving, the following signs may indicate a faulty sway bar stabilizer link: (1).Rattling and thumping noises on rough roads. (2).Imprecise vehicle handling. (3).Stronger inclination of the vehicle during cornering. If the sway bar stabilizer link is found to be defective, it should be replaced as described below. Picture(A) 1.Raise vehicle and remove front wheels. Tip:Always check both stabilizer links and replace them in pairs if necessary. 2.Spray fastening nuts of the stabilizer link with rust remover and let act for a few minutes. Picture(B) 3.Loosen the lower fastening nut of the stabilizer link at the stabilizer and remove. Tip:If the ball stud also starts to turn, hold it with a suitable tool. 4.Press stabilizer link out of torsion bar. Picture(C) 5.Loosen the upper fastening nut of the stabilizer link at the suspension strut and remove it. Tip:If the ball stud also starts to turn, hold it with a suitable tool. Picture(D) 6.Press stabilizer link at suspension strut out of bracket. Picture(E) 7.Insert new stabilizer link at suspension strut. Picture(F) 8.Tighten stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(G) 9.Insert new stabilizer link at stabilizer. 10.Tighten stabilizer link at stabilizer to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(H) 11.Remount the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. Tip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension. 12.Conclude with a test drive. Tie-Rod End Replacement Guideline: If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods. Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely. This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod. Picture(A) Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance. 1.Lift the vehicle and dismount the front axle wheels. 2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes. Picture(B) 3.Dismount the front underride guard. Picture(C) 4.Loosen the fastening nut from the tie rod and remove it completely. 5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator. Picture(D) 6.Remove the clamp of the bellow on the steering gear. 7.Push the bellow towards the tie rod end. Picture(E) 8.Unscrew the inner tie rod from the rack. 9.Clean the sealing face of the bellow at the steering gear. Picture(F) 10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle. Note:Always use new self-locking nuts and bolts for a reliable repair. 11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle manufacturer. Picture(G) 12.Mount the bellow and close the clamps with the appropriate special tool. Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance. Picture(H) 13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer. Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure. Tip:Secure the ball stud against twisting with a suitable tool. Picture(I) 14.Mount the front underride guard. 15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer. 16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications. 17.Perform a test drive. Note:When performing the test drive, pay special attention to the handling while cornering and listen for possible noise emission. Frequently Asked Questions (1).Do I need to replace the control arm if the bushings are worn? Because the weight of the car is transferred through the control arm two rubber bushings are fitted at the pivot point and bolted to the frame. Road conditions and driving habits can contribute to the wear of these bushings which will become worn and fall apart. These bushing can be inspected by raising the car up and looking for an irregular configuration of the rubber center of the bushing. Many control arms have the ball joint manufactured into the arm which will be replaced along with the control arm itself. When one control arm is worn it is highly advised to replace the opposing arm. (2).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel. Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control. If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious. Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car. (3).What happens if I don’t replace ball joints? If you don’t want to replace your ball joints, then get ready to experience some serious issues. The old ball joints cause mysterious clunking noise or drifting steering. Once they are worn-out, it will seriously affect your steering and suspension. However, you do not need to change the ball joints if it is new. DiscountShippingWarrantyReturnFeedback Targeted Disounts Terms (1).Targeted Discount Terms only apply to auto parts purchased from CARMASUSPENSIONS, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).If you have reached any targeted discount threshold(s), please contact our customer services after you received all your items. (3).Targeted Discount will be refunded from buyer’s payment, which means CARMASUSPENSIONS won’t provide any extra targeted discounts if full refund is issued. Targeted Shipping Discount (4).Since our warehouse is located in Los Angeles, California, therefore you are qualified for extra 2% targeted shipping discount off the item sales if shipping address of your order is in California(CA), Washington(WA), Oregon(OR), Nevada(NV). If you have reached this targeted shipping discount threshold, please contact our customer services after you received all your items. Note: Item sales means your payment for the product(s) only, excluding shipping and handling charges, US internet sales taxes. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).CARMASUSPENSIONS has the final power of interpretation of all the above Targeted Discount Terms and Procedures. WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm. (1).Warehouse is located in Los Angeles, California, where local pickup transaction is temporarily not available. (2).Shipping services only cover 48 states and Washington DC in US Continental, while most of the time Alaska, Hawaii, Puerto Rico, American Samoa, U.S. Virgin Islands, Northern Marianas, Guam are not deliverable. (3).USPS PO Box, APO Army Post Office, FPO Fleet Post Office addresses are not available. (4).Global Shipping Program is temporarily not available due to the reason for package dimensions. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Your auto parts sometimes might be shipped with two or more separated packages due to weight limitation, please keep patient with no Item Not Received claim or Return request filed until by all of your items are received. (7).Seller is required to purchase signature confirmation to be protected if a buyer reports an item not received or opens a payment dispute if the order has a total cost (including shipping costs and any taxes) of $750 or more. Items valued over $15 on eBay that include a warranty or service contract must contain additional details in seller’s listing description. 10 Year Warranty Terms and Procedures (1).The warranty terms only apply to the auto parts purchased from CARMASUSPENSIONS, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).CARMASUSPENSIONS carries no warranty responsibilities for any auto parts removing fees, installation fees, consulting fees, labor costs, towing charges, rental car reimbursements. (3).The stated 10 year warranty is limited to only one brand new replacement for each part purchased during 10 year warranty time period. (4).CARMASUSPENSIONS promises free replacement due to quality defects or item not as described issues within 90 calendar days from the date when buyers receive their items in the situation when buyers are willing to provide convictive proofs or professional diagnose report if required, otherwise CARMASUSPENSIONS has the right to refuse any replacement requests. (5).CARMASUSPENSIONS promises free replacement due to quality defects or item not as described issues after 90 calendar days from the date when buyers receive their items in the situation when buyers promise to prepay 15% of the original item sales price as postage for replacement, otherwise CARMASUSPENSIONS has the right to refuse any replacement requests. (6).CARMASUSPENSIONS carries no warranty responsibilities for any replacement due to car accidents, drag racing, unprofessional replacement, road hazard, disassembly. (7).Anyone who attempts to execute 10 year warranty procedures must be the original purchaser of the item(s), otherwise 10 year warranty terms void immediately. (8).Anyone who attempts to execute 10 year warranty procedures must provide screenshot of his or her original eBay order details if required, including buyer user name, shipping address, item title, item id, final sales price. (9).CARMASUSPENSIONS has the final power of interpretation of the above 10 Year Warranty Terms and Procedures. (1).Most of items support 60 Days Money Back Guarantee. (2).Refunds will be credited within 2 or 3 business days after returned item(s) is received. Copyright of carmasuspensions. All rights reserved.

Frequently Asked Questions About For Nissan Pathfinder 1998-2003 Infiniti QX4 Rear Shocks Struts Absorbers in My Website

www.fibusfamilyfoundation.org is the best online shopping platform where you can buy For Nissan Pathfinder 1998-2003 Infiniti QX4 Rear Shocks Struts Absorbers from renowned brand(s). www.fibusfamilyfoundation.org delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.

What are the best-selling For Nissan Pathfinder 1998-2003 Infiniti QX4 Rear Shocks Struts Absorbers on www.fibusfamilyfoundation.org?

Frequently Asked Questions About For Nissan Pathfinder 1998-2003 Infiniti QX4 Rear Shocks Struts Absorbers in My Website

What are the best-selling For Nissan Pathfinder 1998-2003 Infiniti QX4 Rear Shocks Struts Absorbers on www.fibusfamilyfoundation.org?

Leave a Reply Cancel reply